[Meego-porting] [MeeGo-dev] [Meego]Error when booting beagle board with Meego.

Mon Dec 20 02:01:02 PST 2010

Hi Amit

I can see below version of MLO and u-boot.bin being downloaded while running the script to write to SD card.
Please check if you faced the same issue of version mismatch.

***********CLIP*********************

1 / 7: Downloading X-loader and Uboot

2010-12-20 15:15:23 URL:http://rcn-ee.net/deb/tools/latest/bootloader [851/851] -> "/root/new_beagle_image/17Dec/setup/downloads/bootloader" [1]

2 / 7: Unmountting Partitions

WARNING: DOS-compatible mode is deprecated. It's strongly recommended to
         switch off the mode (command 'c') and change display units to
         sectors (command 'u').

Command (m for help): Command action
   e   extended
   p   primary partition (1-4)
Partition number (1-4): First cylinder (1-969, default 1): Last cylinder, +cylinders or +size{K,M,G} (1-969, default 969): 
Command (m for help): Partition number (1-4): 
Command (m for help): Selected partition 1
Hex code (type L to list codes): Changed system type of partition 1 to e (W95 FAT16 (LBA))

Command (m for help): 
Disk /dev/sdc: 7973 MB, 7973371904 bytes
255 heads, 63 sectors/track, 969 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x000023bc

   Device Boot      Start         End      Blocks   Id  System
/dev/sdc1   *           1           9       72261    e  W95 FAT16 (LBA)

Command (m for help): The partition table has been altered!

Calling ioctl() to re-read partition table.

WARNING: If you have created or modified any DOS 6.x
partitions, please see the fdisk manual page for additional
information.
Syncing disks.

3 / 7: Formatting Boot Partition

mkfs.vfat 3.0.7 (24 Dec 2009)
`/root/new_beagle_image/17Dec/setup/downloads/MLO-beagleboard-1.44+r16+gitr1c9276af4d6a5b7014a7630a1abeddf3b3177563-r16' -> `/root/new_beagle_image/17Dec/setup/disk/MLO'
`/root/new_beagle_image/17Dec/setup/downloads/u-boot-beagleboard-2010.03+r65+gitrca6e1c136ddb720c3bb2cc043b99f7f06bc46c55-r65.bin' -> `/root/new_beagle_image/17Dec/setup/disk/u-boot.bin'
done
***************CLIP*************************************************

Also 

-----Original Message-----
From: meego-porting-bounces at lists.meego.com on behalf of Amit Pundir
Sent: Mon 12/20/2010 3:04 PM
To: Development for the MeeGo Project (discussion list)
Subject: Re: [Meego-porting] [MeeGo-dev] [Meego]Error when booting beagle board with Meego.

I got a sort of similar issue when I followed the page
http://wiki.meego.com/ARM/Meego_on_Beagleboard_from_scratch recently and my
u-boot hang forever on a Beagle Rev C3 board.

I don't have the exact logs and the error was something like the following
where u-boot hangs for eternity:
--------------
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
--------------

I looked up google for known issues and found this
http://groups.google.com/group/beagleboard/browse_thread/thread/93ebb6c89cd00e76/5bac04642cb0bf15.
So I'm suspecting this MLO(x-loader)/u-boot version conflict issue,
atleast in my case.

Regards,
Amit Pundir

On Mon, Dec 20, 2010 at 12:24 PM, Leo <leo20090916 at gmail.com> wrote:

> I always met the this problem, I'm not sure the same with yours, It's just
> boot file damaged.
> Generally, I copy from the PC, and insert it to my develop-board again,
> then worked.
>
> 2010/12/20 <rajeevranjan.kumar at wipro.com>
>
>>  Hi
>>
>> Facing problem in booting beagle board with Meego. Please suggest how to
>> solve this problem.
>>
>> My beagle board is  based on processor OMAP35x of Texas Instrument (TI).
>> Processor OMAP35x
>> is integrated with 600MHz ARM Cortex(tm)-A8 core and 412MHz DSP core   which
>> can process and calculate the digital signals.
>>
>>  Created  beagle board image . Finally written image on SD card. Followed
>> steps mentioned in wiki page to create image and writing image.
>>
>> http://wiki.meego.com/ARM/Meego_on_Beagleboard_from_scratch.
>>
>>
>> Then  started my beagle board and pressed boot button to boot using SD
>> card
>>
>> *but this gives below Error:
>>
>> Texas Instruments X-Loader 1.4.4ss ( Sep   22  2010 - 1 6 :1 2 : 19 )
>> Unknown chip: mfr was 0x2c, id was 0xb1
>> Unsupported Chip!
>>
>> *Thanks
>> Rajeev
>>
>> _______________________________________________
>> MeeGo-porting mailing list
>> MeeGo-porting at lists.meego.com
>> http://lists.meego.com/listinfo/meego-porting
>>
>>
>
> _______________________________________________
> MeeGo-dev mailing list
> MeeGo-dev at meego.com
> http://lists.meego.com/listinfo/meego-dev
>
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.meego.com/pipermail/meego-porting/attachments/20101220/a402c6ad/attachment.html>